afastainlesskb
1 Attending
eDEEJAY is available on mobile devices.
Keep connected with us everywhere !
Keep connected with us everywhere !
Monday, July 22, 2019 11:39 am - 2:39 pm
Leanhu Village, Mazhu Town ,Yuyao , Zhejiang , China
Leanhu Village, Mazhu Town ,Yuyao , Zhejiang , China
Yuyao
315450
China
Did you find that the stainless steel faucets in your home will become smaller and smaller after using them for a while? Some people may think that the water pressure is low, open other taps, and the water flow is normal. Looking for outsiders to repair, for various reasons let you change this, and the problem of spending money is not so complicated, so let us see what caused it?
First prepare tools for inspecting and repairing stainless steel faucets: small folding shears, new toothbrushes
Then follow the steps below to review and resolve this issue:
1. Unscrew the faucet filter counterclockwise. If it does not move, use a pliers to unscrew the mat and the mat will prevent damage to the filter.
2 The filter is facing down and the top of the filter is pressed upwards to push the plastic filter element out.
3. Place the plastic filter element under the faucet, gently scrub with a toothbrush, and then wash a small piece of scale on it.
4. Assemble the cleaned filter and screw it back onto the faucet. it is good! Solve the problem in three easy steps.
5. Level the filter element. With the green filter one end up, gently insert the small cutting tip into the side seam according to the diagram and remove the green cone filter.
6. Hold the filter element, insert the small scissors into the rectangular hole with your right hand, and forcibly remove the second layer of the filter cover from the upper side. The third and fourth layered gratings are then poured out.
7. Clean the assembly with a toothbrush.
8. Insert the fourth and third gratings and the second disc-shaped filter cover into the filter element in the reverse order of the decomposition, and finally press the green cone filter into the filter card slot. in. Small cut.
9. Insert the combined filter element into the filter in the direction of the arrow. When installing, be careful that the filter element should be flush with the filter to avoid poor installation when screwing in the faucet.
10 Rotate the filter clockwise. Turn on the tap, just like a stream of water!
Finally, the conclusion is that the faucet is not used for a long time. Usually, there are no component failures. Most of them are caused by scale or other impurities. In particular, faucets that use solar water are often prone to blockage during the summer.
For better quality faucets, the fine sand gauge is mainly concentrated on the first green cone filter. Simply clean the layer filter and the plastic filter elements do not need to be disassembled and cleaned. If the diameter of the cone filter is greater than 0.5 mm, consider removing the plastic filter.
information about stainless steel faucets : https://www.afastainlesskb.com/product/stainless-s...
First prepare tools for inspecting and repairing stainless steel faucets: small folding shears, new toothbrushes
Then follow the steps below to review and resolve this issue:
1. Unscrew the faucet filter counterclockwise. If it does not move, use a pliers to unscrew the mat and the mat will prevent damage to the filter.
2 The filter is facing down and the top of the filter is pressed upwards to push the plastic filter element out.
3. Place the plastic filter element under the faucet, gently scrub with a toothbrush, and then wash a small piece of scale on it.
4. Assemble the cleaned filter and screw it back onto the faucet. it is good! Solve the problem in three easy steps.
5. Level the filter element. With the green filter one end up, gently insert the small cutting tip into the side seam according to the diagram and remove the green cone filter.
6. Hold the filter element, insert the small scissors into the rectangular hole with your right hand, and forcibly remove the second layer of the filter cover from the upper side. The third and fourth layered gratings are then poured out.
7. Clean the assembly with a toothbrush.
8. Insert the fourth and third gratings and the second disc-shaped filter cover into the filter element in the reverse order of the decomposition, and finally press the green cone filter into the filter card slot. in. Small cut.
9. Insert the combined filter element into the filter in the direction of the arrow. When installing, be careful that the filter element should be flush with the filter to avoid poor installation when screwing in the faucet.
10 Rotate the filter clockwise. Turn on the tap, just like a stream of water!
Finally, the conclusion is that the faucet is not used for a long time. Usually, there are no component failures. Most of them are caused by scale or other impurities. In particular, faucets that use solar water are often prone to blockage during the summer.
For better quality faucets, the fine sand gauge is mainly concentrated on the first green cone filter. Simply clean the layer filter and the plastic filter elements do not need to be disassembled and cleaned. If the diameter of the cone filter is greater than 0.5 mm, consider removing the plastic filter.
information about stainless steel faucets : https://www.afastainlesskb.com/product/stainless-s...